AAHolybro Microhard Radio have been configured to Point to Point Operating Mode and 57600 Serial Baud Rate in factory. Using these parameters, the Radio can communicates successfully with the Pixhawk series flight controller. After Firmware Update or resetting the Radio, you can re-config them as following.
In Point to Point operating modes, there must be a master to provide network synchronization for the system, so one Radio should be configured to PP Master and another should be configured to PP Remote. Refer to Operating Manual for the detail information of Radio Configuration.
About The Author
pixhawk
Other Posts by This Author
XBP9X Radio Status LEDs
pixhawkJuly 11, 20250 Comments
Status LEDs The radios have 6 status LEDs, there blue, two orange and one green. The meaning of…
XBP9X Radio Specification
pixhawkJuly 11, 20250 Comments
Product Specification FREQUENCY RANGEISM 902 to 928 MHzTRANSMIT POWER (Software Selectable)Up to 30 dBm*CHANNELS10 hopping sequences share 50…
XBP9X Radio Power
pixhawkJuly 11, 20250 Comments
Supply voltage 5V DC from USB or 6-position JST-GH (100mW) 7~35V DC form 4-position JST-GH (500mW or 1000mW)…
XBP9X Radio Point-to-Multipoint Setup with XBee Radio
pixhawkJuly 11, 20250 Comments
Holybro XBP9X Radio Point-to-Multipoint setup: Use the XCTU configuration software to set the CM, HP, ID, MT, BR…
XBP9X Radio Pinout
pixhawkJuly 11, 20250 Comments
Data Port PinSignalVolt1(red)NC—2(black)RX+3.3V3(black)TX+3.3V4(black)CTS+3.3V5(black)RTS+3.3V6(black)GNDGND Power Port PinSignalVolt1(red)BAT+7-35V2(red)BAT+7-35V3(black)BAT-GND4(black)BAT-GND
XBP9X Radio Download
pixhawkJuly 11, 20250 Comments
XCTUDigi XBee SX 900 RF Module4MBXBee-Radio-Case.stp
XBP9X Radio Antenna
pixhawkJuly 11, 20250 Comments
SpecificationsQT900LFrequency range902锝?28 MHzBand Width26 MHzPolarizationverticalGain3 dBiInput impedance50惟SWR鈮?.5Maximum power20WConnectorRPSMA (female)Total length19.6 cm (foldable antenna)Weight40g
Related Posts
Microhard Radio Download
pixhawkJuly 11, 20250 Comments
7MBPico Series P400 P840.Operating Manual.v1.4.6.pdfpdf7MBPico Series P400.Operating Manual.v1.4.6.pdfpdf6MBPico Series P900.Operating Manual.v1.8.7.pdfpdf3MBPicoConfig_1_10.ziparchive5MBMicrohard-Case.stp
Microhard Radio Enabling RTS / CTS Flow Control
pixhawkJuly 11, 20250 Comments
The flow control of the Microhard Telemetry Radio module is turned off by default, and can be turned…
Microhard Radio Overview
pixhawkJuly 11, 20250 Comments
Holybro Microhard Telemetry Radio integrates microhard Pico Series RF module which is capable of delivering high-performance wireless serial…
Microhard Radio Pinout
pixhawkJuly 11, 20250 Comments
Data Port PinSignalVolt1(red)NC—2(black)RX+3.3V3(black)TX+3.3V4(black)CTS+3.3V5(black)RTS+3.3V6(black)GNDGND Diagnostic Port PinSignalVolt1NC—2(black)RX+3.3V3(black)TX+3.3V4(black)GNDGND Power Port PinSignalVolt1(red)BAT+7-35V2(red)BAT+7-35V3(black)BAT-GND4(black)BAT-GND
Microhard Radio Point-to-Multipoint Setup with Microhard Radio
pixhawkJuly 11, 20250 Comments
Sample Wiring Diagram Note that the above Diagram shows RTK connection, but the telemetry connections apply to normal…
Microhard Radio Ports & Buttons
pixhawkJuly 11, 20250 Comments
Power Port (4-position JST-GH) The input Voltage range is 7-35 VDC. The Radio must be powered by this…
Microhard Radio Specification
pixhawkJuly 11, 20250 Comments
Specification P900P840P400-C1SFrequency Range902 to 928 MHz840 to 845 MHz410 to 480 MHzTransmit Power (Software Adjustable)100mW to 1W (20-30dBm)…
Microhard Radio Status LED
pixhawkJuly 11, 20250 Comments
AAMicrohard Radio have 6 status LEDs, there are three blue, two orange and one green LEDs. The meaning…
Leave a Reply