Pixhawk 6C Supported Firmware

May 30, 2025 pixhawk Pixhawk 6C

Pixhawk 6C ships with PX4 FMUv6C Firmware

PX4
Pixhawk 6C is supported on PX4 1.13.1 release and later.

Ardupilot
Pixhawk 6C is supported in Ardupilot 4.2.3 stable release and later. Firmware can be flash via Mission Planner or QGroundControl. It can also be downloaded here: https://firmware.ardupilot.org/

QGroundControl
Must use QGC v4.2.4 or later, or Daily QGC Build.

About The Author

pixhawk

Other Posts by This Author

XBP9X Radio Status LEDs

pixhawkJuly 11, 20250 Comments

Status LEDs The radios have 6 status LEDs, there blue, two orange and one green. The meaning of…

XBP9X Radio Specification

pixhawkJuly 11, 20250 Comments

Product Specification FREQUENCY RANGEISM 902 to 928 MHzTRANSMIT POWER (Software Selectable)Up to 30 dBm*CHANNELS10 hopping sequences share 50…

XBP9X Radio Power

pixhawkJuly 11, 20250 Comments

Supply voltage 5V DC from USB or 6-position JST-GH (100mW) 7~35V DC form 4-position JST-GH (500mW or 1000mW)…

XBP9X Radio Point-to-Multipoint Setup with XBee Radio

pixhawkJuly 11, 20250 Comments

Holybro XBP9X Radio Point-to-Multipoint setup: Use the XCTU configuration software to set the CM, HP, ID, MT, BR…

XBP9X Radio Pinout

pixhawkJuly 11, 20250 Comments

Data Port PinSignalVolt1(red)NC—2(black)RX+3.3V3(black)TX+3.3V4(black)CTS+3.3V5(black)RTS+3.3V6(black)GNDGND Power Port PinSignalVolt1(red)BAT+7-35V2(red)BAT+7-35V3(black)BAT-GND4(black)BAT-GND

XBP9X Radio Download

pixhawkJuly 11, 20250 Comments

XCTUDigi XBee SX 900 RF Module4MBXBee-Radio-Case.stp

XBP9X Radio Dimension

pixhawkJuly 11, 20250 Comments

XBP9X Radio Antenna

pixhawkJuly 11, 20250 Comments

SpecificationsQT900LFrequency range902锝?28 MHzBand Width26 MHzPolarizationverticalGain3 dBiInput impedance50惟SWR鈮?.5Maximum power20WConnectorRPSMA (female)Total length19.6 cm (foldable antenna)Weight40g

Related Posts

Pixhawk 6C Overview

pixhawkMay 30, 20250 Comments

The Pixhawk® 6C is the latest update to the successful family of Pixhawk® flight controllers, based on the…

Pixhawk 6C Technical Specification

pixhawkMay 30, 20250 Comments

Processors & Sensors FMU Processor: STM32H743 32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM IO Processor: STM32F103…

Pixhawk 6C Ports

pixhawkMay 30, 20250 Comments

Pixhawk 6C Ports I/O PWM OUT = MAIN OUT FMU PWM OUT = AUX OUT Pin 1 starts…

Pixhawk 6C Sample Wiring Diagram

pixhawkMay 30, 20250 Comments

Pixhawk 6C Sample Wiring Diagram

Pixhawk 6C Dimensions

pixhawkMay 30, 20250 Comments

Dimension in millimeters

Pixhawk 6C System Diagram & Pinout

pixhawkMay 30, 20250 Comments

Pixhawk 6C & Pix32 v6 shares the same System Diagram & Pinout

Pixhawk 6C PX4 & Ardupilot Guide

pixhawkMay 30, 20250 Comments

PX4 Autopilot If you are using PX4 Autopilot, please refer to the PX4 user guide page for additional…

Pixhawk 6C PWM Signal Voltage MOD

pixhawkMay 30, 20250 Comments

The newest batch (version RC09) of Pixhawk 6C now supports switchable PWM signal voltage (3.3V or 5V). The…

Leave a Reply Cancel reply