Category: Radio
Remote ID
SiK Telemetry Radio V3
XBP9X Radio
Categories
Microhard Radio Pinout
Data Port PinSignalVolt1(red)NC—2(black)RX+3.3V3(black)TX+3.3V4(black)CTS+3.3V5(black)RTS+3.3V6(black)GNDGND Diagnostic Port PinSignalVolt1NC—2(black)RX+3.3V3(black)TX+3.3V4(black)GNDGND Power Port PinSignalVolt1(red)BAT+7-35V2(red)BAT+7-35V3(black)BAT-GND4(black)BAT-GND
Sample Wiring Diagram Note that the above Diagram shows RTK connection, but the telemetry connections apply to normal GPS as well. Point to Multipoint Connection Using Microhard Radio Telemetry Radio Setup First, Select one of the Radios as the Master, and the other Radios as the Remote. Use the Pico configurator to set the Master […]
Categories
Microhard Radio Ports & Buttons
Power Port (4-position JST-GH) The input Voltage range is 7-35 VDC. The Radio must be powered by this Power Port. Please connect to a power supply when in use and during configuration. Config Button Holding this button while powering-up the radio will boot the unit into COMMAND mode: the default serial interface will be active […]
Categories
Microhard Radio Specification
Specification P900P840P400-C1SFrequency Range902 to 928 MHz840 to 845 MHz410 to 480 MHzTransmit Power (Software Adjustable)100mW to 1W (20-30dBm) 100mW to 1W (20-30dBm) 100mW to 1W (20-30dBm) Link RateUp to 276 kbpsUp to 345 kbpsUp to 345 kbpsSerial Baud RateUp to 230.4kbps asynchronous300 bps to 230 kbps300 bps to 230 kbpsSpreading MethodFrequency Hopping Spread Spectrum (FHSS)Frequency […]
Categories
Microhard Radio Status LED
AAMicrohard Radio have 6 status LEDs, there are three blue, two orange and one green LEDs. The meaning of the different LEDs are: Power LED(green) This LED will illuminate when the Radio is connected to a power source (7-35VDC). TX LED (orange) When illuminated, this LED indicates that the Radio is transmitting data over the […]
Categories
Remote ID Download
STP file 2MBremote-id-v001-1025_asm.stp
Categories
Remote ID Firmware Support
The Holybro RemoteID uses the ArduRemoteID FW, the firmware is already installed on the module. The latest version can be found here: https://github.com/ArduPilot/ArduRemoteID/releases Ardupilot Ardupilot has support for Remote ID in version 4.x and newer. See this link for more information: https://ardupilot.org/dev/docs/opendroneid.html#opendroneid PX4 PX4 has support for Remote ID in version PX4 v1.14 and newer. […]
Categories
Remote ID Firmware Update
Upgrading FW via OTA (Preferred) Once powered on, the Module will act as a WiFi Access Point. Connect to the RID_xxxxxxxxxxx WiFi network, and the default password is ArduRemoteIDAfter connecting to this WiFi network, point your browser to http://192.168.4.1At the bottom of the page, you can upload and flash the new firmware.Download the ArduRemoteID_Holybro_RemoteID_OTA.bin file […]
Categories
Remote ID Overview & Spec
AAHolybro RemoteID Module is low cost, small size, and light weight module that broadcast information about UAVs in flight through WIFI & Bluetooth. It supports both CAN and serial protocols. It is a FCC & CE approved radio module.The products run open-source firmware (ArduRemoteID) and provides a so-called standard Remote ID solution, primarily target drone […]